Siser Cutting, Application and Care

Please note that these are the recommended settings as per Siser's website however, you should always test cut before attempting any new medium

Siser EasyWeed



Cutting

Cricut:


Blade: Standard

Setting: Iron-on

Silhouette Cameo:

Blade: Standard, 3

Material: Heat Transfer, Smooth
Speed: 8
Force: 6

Scan N Cut:


Blade: Standard, 2

Cut Speed: 1
Cut Pressure: 1

Roland GS/GX-24:

Blade: 45°

Gram Force: 80-90
Offset: .250
Speed: 25-50 cm/s

Graphtec:


Blade: 45°

Gram Force: 8-9
Tool: CB09U+0
Speed: 30 cm/s

Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.

Application

Application instructions (home iron)

• Set iron dial between Cotton and Linen
• Cover design with Kraft paper or non-stick cover sheet
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet
and re-press for 5-10 seconds
• Peel carrier hot or cold
Application Instructions (heat press)

• Cut in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 305°F/150°C
• Use medium pressure for 10-15 seconds
• Peel carrier hot or cold

 

Care

EasyWeed Applies to:

100% cotton
Poly/cotton blends
100% polyester
Leather

Recommended Accessories:

Siser Weeder
Multipurpose Paper or
Kraft Paper or
Heat Transfer Cover Sheet

Laundering:

Wait 24 hours before 1st wash
Machine wash warm or cold / mild detergent
Dry on normal dryer setting
Do not dry clean

 

Siser EasyWeed Stretch



Cutting

Cricut:


Blade: Standard

Setting: Iron-On

Silhouette Cameo:

Blade: Standard, 3

Material: Heat Transfer, Smooth
Speed: 8
Force: 6

Scan N Cut:


Blade: Standard, 2

Cut Speed: 1
Cut Pressure: 1

Roland GS/GX-24:

Blade: 45°

Gram Force: 60-70
Offset: .250
Speed: 30 cm/s

Graphtec:


Blade: 45°

Gram Force: 9-10
Tool: CB09U+0
Speed: 30 cm/s

Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.

Application

Application instructions (home iron)

• Set iron dial between Cotton and Linen
• Cover design with Kraft paper or non-stick cover sheet
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet
and re-press for 5-10 seconds
• Peel carrier hot or cold
Application Instructions (heat press)

• Cut in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 305°F/150°C
• Use medium/firm pressure for 15 seconds
• Peel carrier hot or cold

Care

EasyWeed Stretch Applies to:

 

100% cotton
Poly/cotton blends
100% polyester
Leather
Lycra®/Spandex

Recommended Accessories:

 

Siser Weeder
Multipurpose Paper or
Kraft Paper or
Heat Transfer Cover Sheet

Laundering:

 

Wait 24 hours before 1st wash
Machine wash cold / mild detergent
Dry on normal dryer setting
Do not dry clean


Siser Glitter



Cutting

Cricut:


Blade: Standard

Setting: Iron On+

Silhouette Cameo:

Blade: Standard, 4

Material: Heat Transfer, Smooth
Speed: 8
Force: 11

Scan N Cut:


Blade: Standard, 3

Cut Speed: 1
Cut Pressure: 5

Roland GS/GX-24:

Blade: 45°

Gram Force: 180-190
Offset: .250
Speed: 30 cm/s

Graphtec:


Blade: 45°

Gram Force: 17
Tool: CB09U+0
Speed: 30 cm/s

Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.

Application

Application instructions (home iron)

• Set iron dial between Cotton and Linen
• Cover design with Kraft paper or non-stick cover sheet
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet
and re-press for 10 seconds
• Peel carrier warm
Application Instructions (heat press)

• Cut in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 320°F/160°C
• Use firm pressure for 15-20 seconds
• Peel carrier warm

Care

Glitter Applies to:

 

100% cotton
Poly/cotton blends
100% polyester
Leather

Recommended Accessories:

 

Siser Weeder
Multipurpose Paper or
Kraft Paper or
Heat Transfer Cover Sheet

Laundering:

 

Wait 24 hours before 1st wash
Machine wash warm or cold / mild detergent
Dry on normal dryer setting
Do not dry clean


Siser Holographic



Cutting

Cricut:

Blade: Standard

Setting: Light Cardstock

Silhouette Cameo:

Blade: Standard, 3

Setting: Heat Transfer,
Smooth
Speed: 8
Force: 14

Scan N Cut:


Blade: Standard, 2

Cut Speed: 1
Cut Pressure: 3

Roland GS/GX-24:

Blade: 45°
Gram Force: 180-190
Offset: .250
Speed: 30 cm/s

Graphtec:

 

Blade: 45°
Gram Force: 17-18
Tool: CB09U+0
Speed: 30 cm/s

Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.

Application

Application instructions (home iron)

• Set iron dial between Cotton and Linen
• Cover design with Kraft paper or non-stick cover sheet
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 10-15 seconds
• If areas of design lift after application, replace cover sheet
and re-press for 5-10 seconds
• Peel carrier cold
Application Instructions (heat press)

• Cut in reverse
• Weed excess material
• Preheat garment for 2-3 seconds
• Apply design at 320°F/160°C
• Use medium pressure for 15-20 seconds
• Peel carrier cold

Care

Holographic Applies to:

 

100% cotton
Poly/cotton blends
100% polyester
Leather

Recommended Accessories:

 

Siser Weeder
Multipurpose Paper or
Kraft Paper or
Heat Transfer Cover Sheet

Laundering:

 

Wait 24 hours before 1st wash
Machine wash warm or cold / mild detergent
Dry on normal dryer setting
Do not dry clean

Further Information can be found at: www.siserna.com